Aggarwal anoop (45 resultados)

Condición: New. pp. 64.

Condición: New. pp. 100.

paperback. Condición: New. NEW. SHIPS FROM MULTIPLE LOCATIONS. book.

Taschenbuch. Condición: Neu. Micro Drilling of Hard to Cut Alloys with Electric Discharge Machining | Anoop Aggarwal (u. a.) | Taschenbuch | 100 S. | Englisch | 2014 | LAP LAMBERT Academic Publishing | EAN 9783659154461 | Verantwortliche Person für die EU: preigu GmbH & Co. KG, Lengericher Landstr. 19, 49078 Osnabrück, mail[at]preigu[dot]de | Anbieter: preigu. …

Condición: New. Print on Demand pp. 64 2:B&W 6 x 9 in or 229 x 152 mm Perfect Bound on Creme w/Gloss Lam.

Condición: New. PRINT ON DEMAND pp. 64.

Taschenbuch. Condición: Neu. This item is printed on demand - it takes 3-4 days longer - Neuware -Conventional drilling is a multipoint, end cutting tool that involves cutting of a hole into a solid. The present work entailed the use of Electric Discharge Machining (EDM)technique to produce micro-holes in two different materials using copper and brass electrode tubes. The workpiece materials were selected on the basis of their use in biomedical implants and aerospace engineering. Optimization of the factors and their levels were accomplished using L-16 orthogonal array by Taguchi method. It was observed that workpiece material S.S.-316L can be best machined with brass electrode-tube material at 3.0 ampere peak current and 75% duty factor. On the other hand, Ti-6Al-4V was found to be best machined with copper electrode-tube material at 3.0 ampere peak current and 50% duty factor. 100 pp. Englisch.…

Condición: New. Dieser Artikel ist ein Print on Demand Artikel und wird nach Ihrer Bestellung fuer Sie gedruckt. Autor/Autorin: Jain SanjivDr. Sanjiv Jain is serving as an Associate Professor and Head in the Department of Mechanical Engineering at Ambala College of Engineering & Applied Research, Haryana (India). His area of interest is ISO 9000 and Lean Manu. …

Condición: New. Dieser Artikel ist ein Print on Demand Artikel und wird nach Ihrer Bestellung fuer Sie gedruckt. Autor/Autorin: Jain GauravMr. Gaurav Jain is serving as an Assistant Professor in the School of Mechanical Engineering, Chitkara University, Punjab, India. His area of interest is Metal Cutting.Mr. Anoop Aggarwal is serving as an Assistant Professo.…

Taschenbuch. Condición: Neu. nach der Bestellung gedruckt Neuware - Printed after ordering - Conventional drilling is a multipoint, end cutting tool that involves cutting of a hole into a solid. The present work entailed the use of Electric Discharge Machining (EDM)technique to produce micro-holes in two different materials using copper and brass electrode tubes. The workpiece materials were selected on the basis of their use in biomedical implants and aerospace engineering. Optimization of the factors and their levels were accomplished using L-16 orthogonal array by Taguchi method. It was observed that workpiece material S.S.-316L can be best machined with brass electrode-tube material at 3.0 ampere peak current and 75% duty factor. On the other hand, Ti-6Al-4V was found to be best machined with copper electrode-tube material at 3.0 ampere peak current and 50% duty factor.…

Condición: New. Print on Demand pp. 100 2:B&W 6 x 9 in or 229 x 152 mm Perfect Bound on Creme w/Gloss Lam.

Condición: New. Dieser Artikel ist ein Print on Demand Artikel und wird nach Ihrer Bestellung fuer Sie gedruckt. Autor/Autorin: Aggarwal AnoopMr. Anoop Aggarwal is serving as an Assistant Professor in the Department of Mechanical Engineering at Chitkara University, Punjab, India. His area of interest is micro-machining of hard to cut metals/alloys. He has to .…

Condición: New. PRINT ON DEMAND pp. 100.

PAP. Condición: New. New Book. Shipped from UK. THIS BOOK IS PRINTED ON DEMAND. Established seller since 2000.

PAP. Condición: New. New Book. Delivered from our UK warehouse in 4 to 14 business days. THIS BOOK IS PRINTED ON DEMAND. Established seller since 2000.

Taschenbuch. Condición: Neu. nach der Bestellung gedruckt Neuware - Printed after ordering - El taladrado convencional es una herramienta de corte multipunto y de punta que consiste en la perforación de un agujero en un material sólido. El presente trabajo consistió en el uso de la técnica de mecanizado por descarga eléctrica (EDM) para producir microagujeros en dos materiales diferentes utilizando tubos de electrodo de cobre y latón. Los materiales de las piezas de trabajo se seleccionaron en función de su uso en implantes biomédicos y en ingeniería aeroespacial. La optimización de los factores y sus niveles se llevó a cabo utilizando una matriz ortogonal L-16 mediante el método de Taguchi. Se observó que el material de la pieza de trabajo S.S.-316L se puede mecanizar mejor con un tubo de electrodo de latón a una corriente máxima de 3,0 amperios y un factor de servicio del 75 %. Por otra parte, se comprobó que el Ti-6Al-4V se mecaniza mejor con un tubo de electrodo de latón a una corriente máxima de 3,0 amperios y un factor de servicio del 50 %.…

Taschenbuch. Condición: Neu. This item is printed on demand - Print on Demand Titel. Neuware -Conventional drilling is a multipoint, end cutting tool that involves cutting of a hole into a solid. The present work entailed the use of Electric Discharge Machining (EDM)technique to produce micro-holes in two different materials using copper and brass electrode tubes. The workpiece materials were selected on the basis of their use in biomedical implants and aerospace engineering. Optimization of the factors and their levels were accomplished using L-16 orthogonal array by Taguchi method. It was observed that workpiece material S.S.-316L can be best machined with brass electrode-tube material at 3.0 ampere peak current and 75% duty factor. On the other hand, Ti-6Al-4V was found to be best machined with copper electrode-tube material at 3.0 ampere peak current and 50% duty factor.OmniScriptum SRL, Str. Armeneasca 28/1, office 1, 2012 Chisinau 100 pp. Englisch.…

Taschenbuch. Condición: Neu. nach der Bestellung gedruckt Neuware - Printed after ordering - Le perçage conventionnel est un procédé de coupe multipoint à l'extrémité de l'outil qui consiste à percer un trou dans un matériau solide. Le présent travail a consisté à utiliser la technique d'électroérosion (EDM) pour réaliser des micro-trous dans deux matériaux différents à l'aide de tubes d'électrode en cuivre et en laiton. Les matériaux des pièces à usiner ont été sélectionnés en fonction de leur utilisation dans les implants biomédicaux et l'ingénierie aérospatiale. L'optimisation des facteurs et de leurs niveaux a été réalisée à l'aide d'un plan orthogonal L-16 selon la méthode de Taguchi. Il a été observé que le matériau de la pièce à usiner S.S.-316L s'usine au mieux avec un tube d'électrode en laiton, à un courant de crête de 3,0 ampères et un facteur de service de 75 %. En revanche, il a été constaté que le Ti-6Al-4V se prêtait le mieux à l'usinage avec un tube d'électrode en laiton, à un courant de crête de 3,0 ampères et un facteur de service de 50 %.…

Taschenbuch. Condición: Neu. This item is printed on demand - it takes 3-4 days longer - Neuware 92 pp. Spanisch.

Taschenbuch. Condición: Neu. This item is printed on demand - it takes 3-4 days longer - Neuware 92 pp. Deutsch.

PAP. Condición: New. New Book. Shipped from UK. THIS BOOK IS PRINTED ON DEMAND. Established seller since 2000.

PAP. Condición: New. New Book. Shipped from UK. THIS BOOK IS PRINTED ON DEMAND. Established seller since 2000.

PAP. Condición: New. New Book. Shipped from UK. THIS BOOK IS PRINTED ON DEMAND. Established seller since 2000.

PAP. Condición: New. New Book. Shipped from UK. THIS BOOK IS PRINTED ON DEMAND. Established seller since 2000.

PAP. Condición: New. New Book. Delivered from our UK warehouse in 4 to 14 business days. THIS BOOK IS PRINTED ON DEMAND. Established seller since 2000.

PAP. Condición: New. New Book. Delivered from our UK warehouse in 4 to 14 business days. THIS BOOK IS PRINTED ON DEMAND. Established seller since 2000.

PAP. Condición: New. New Book. Delivered from our UK warehouse in 4 to 14 business days. THIS BOOK IS PRINTED ON DEMAND. Established seller since 2000.

PAP. Condición: New. New Book. Delivered from our UK warehouse in 4 to 14 business days. THIS BOOK IS PRINTED ON DEMAND. Established seller since 2000.

Taschenbuch. Condición: Neu. Microforatura di leghe difficili da lavorare mediante elettroerosione | Anoop Aggarwal (u. a.) | Taschenbuch | Italienisch | 2026 | Edizioni Sapienza | EAN 9786630120523 | Verantwortliche Person für die EU: preigu GmbH & Co. KG, Lengericher Landstr. 19, 49078 Osnabrück, mail[at]preigu[dot]de | Anbieter: preigu Print on Demand. …

Taschenbuch. Condición: Neu. Microperforación de aleaciones difíciles de cortar mediante mecanizado por descarga eléctrica | Anoop Aggarwal (u. a.) | Taschenbuch | Spanisch | 2026 | Ediciones Nuestro Conocimiento | EAN 9786630060706 | Verantwortliche Person für die EU: preigu GmbH & Co. KG, Lengericher Landstr. 19, 49078 Osnabrück, mail[at]preigu[dot]de | Anbieter: preigu Print on Demand. …