Sinopsis
This book presents an experimental study on diesel spray and mixture formation under both evaporating and non-evaporating conditions in a constant volume chamber. Using tracer laser absorption and scattering (LAS) and diffused background illumination (DBI), the study characterizes spray development and mixture formation. A tracer fuel of 97.5 vol% n-tridecane and 2.5 vol% 1-methylnaphthalene (α-MN) was used to examine liquid and vapor phase distributions during evaporation. Microscopic observations compared near-field spray behavior in transient and quasi-steady states under non-evaporating conditions. Additionally, numerical simulations of nozzle flow provided insights into how nozzle geometry affects spray characteristics. The study compares the effects of small and large injection amounts on spray behavior, using 0.5 and 2.5 mg/hole for LAS experiments and 5.0 mg/hole for microscopic observations. Results show that smaller injection amounts lead to faster dilution but slower evaporation. Single-hole injectors exhibited a shorter transient period compared to multi-hole injectors under non-evaporating conditions, highlighting the impact of nozzle design. To further investigate transient spray behavior, rail pressure was adjusted to 30 MPa to match multi-hole injector profiles at 100 MPa. Injection amounts were controlled around 0.5–0.6 mg/hole. The study found that single-hole injectors had worse vapor penetration, smaller spray angles, and lower turbulent kinetic energy than multi-hole injectors, resulting in less efficient mixture formation. Simulations confirmed that multi-hole injectors induce higher turbulence, enhancing mixture formation. The book also examines split injection strategies, focusing on split ratio and dwell time. A 7:3 split ratio was optimal for achieving a homogeneous lean mixture. The improvement in mixture formation was minimal when dwell time exceeded 120 μs, and shorter penetration was observed with negative dwell times.
"Sinopsis" puede pertenecer a otra edición de este libro.
Resultados de la búsqueda para Diesel Spray and Mixture Formation Processes: Under...
Imagen de archivo
Diesel Spray and Mixture Formation Processes (Paperback)
Impresión bajo demandaLibrería: Grand Eagle Retail, Bensenville, IL, Estados Unidos de America
Calificación del vendedor: 5 de 5 estrellas
Paperback. Condición: new. Paperback. This book presents an experimental study on diesel spray and mixture formation under both evaporating and non-evaporating conditions in a constant volume chamber. Using tracer laser absorption and scattering (LAS) and diffused background illumination (DBI), the study characterizes spray development and mixture formation. A tracer fuel of 97.5 vol% n-tridecane and 2.5 vol% 1-methylnaphthalene (a-MN) was used to examine liquid and vapor phase distributions during evaporation. Microscopic observations compared near-field spray behavior in transient and quasi-steady states under non-evaporating conditions. Additionally, numerical simulations of nozzle flow provided insights into how nozzle geometry affects spray characteristics. The study compares the effects of small and large injection amounts on spray behavior, using 0.5 and 2.5 mg/hole for LAS experiments and 5.0 mg/hole for microscopic observations. Results show that smaller injection amounts lead to faster dilution but slower evaporation. Single-hole injectors exhibited a shorter transient period compared to multi-hole injectors under non-evaporating conditions, highlighting the impact of nozzle design. To further investigate transient spray behavior, rail pressure was adjusted to 30 MPa to match multi-hole injector profiles at 100 MPa. Injection amounts were controlled around 0.5-0.6 mg/hole. The study found that single-hole injectors had worse vapor penetration, smaller spray angles, and lower turbulent kinetic energy than multi-hole injectors, resulting in less efficient mixture formation. Simulations confirmed that multi-hole injectors induce higher turbulence, enhancing mixture formation. The book also examines split injection strategies, focusing on split ratio and dwell time. A 7:3 split ratio was optimal for achieving a homogeneous lean mixture. The improvement in mixture formation was minimal when dwell time exceeded 120 ms, and shorter penetration was observed with negative dwell times. This item is printed on demand. Shipping may be from multiple locations in the US or from the UK, depending on stock availability. Nº de ref. del artículo: 9789999329101
Comprar nuevo
EUR 55,01
Gastos de envío gratis
Se envía dentro de Estados Unidos de America
Se envía dentro de Estados Unidos de America
Cantidad disponible: 1 disponibles
Imagen de archivo
Diesel Spray and Mixture Formation Processes: Under Minimal Fuel Delivery Conditions
Librería: California Books, Miami, FL, Estados Unidos de America
Calificación del vendedor: 5 de 5 estrellas
Condición: New. Nº de ref. del artículo: I-9789999329101
Comprar nuevo
EUR 55,01
Gastos de envío gratis
Se envía dentro de Estados Unidos de America
Se envía dentro de Estados Unidos de America
Cantidad disponible: Más de 20 disponibles
Imagen de archivo
Diesel Spray and Mixture Formation Processes
Librería: PBShop.store US, Wood Dale, IL, Estados Unidos de America
Calificación del vendedor: 5 de 5 estrellas
PAP. Condición: New. New Book. Shipped from UK. Established seller since 2000. Nº de ref. del artículo: L2-9789999329101
Comprar nuevo
EUR 72,23
Gastos de envío gratis
Se envía dentro de Estados Unidos de America
Se envía dentro de Estados Unidos de America
Cantidad disponible: Más de 20 disponibles
Imagen de archivo
Diesel Spray and Mixture Formation Processes
Librería: PBShop.store UK, Fairford, GLOS, Reino Unido
Calificación del vendedor: 4 de 5 estrellas
PAP. Condición: New. New Book. Shipped from UK. Established seller since 2000. Nº de ref. del artículo: L2-9789999329101
Comprar nuevo
EUR 69,94
Envío por EUR 3,81
Se envía de Reino Unido a Estados Unidos de America
Se envía de Reino Unido a Estados Unidos de America
Cantidad disponible: Más de 20 disponibles
Imagen de archivo
Diesel Spray and Mixture Formation Processes: Under Minimal Fuel Delivery Conditions
Librería: Revaluation Books, Exeter, Reino Unido
Calificación del vendedor: 5 de 5 estrellas
Paperback. Condición: Brand New. 155 pages. 6.00x0.35x9.00 inches. In Stock. Nº de ref. del artículo: x-9999329101
Comprar nuevo
EUR 64,18
Envío por EUR 11,57
Se envía de Reino Unido a Estados Unidos de America
Se envía de Reino Unido a Estados Unidos de America
Cantidad disponible: 2 disponibles
Imagen de archivo
Diesel Spray and Mixture Formation Processes (Paperback)
Impresión bajo demandaLibrería: CitiRetail, Stevenage, Reino Unido
Calificación del vendedor: 5 de 5 estrellas
Paperback. Condición: new. Paperback. This book presents an experimental study on diesel spray and mixture formation under both evaporating and non-evaporating conditions in a constant volume chamber. Using tracer laser absorption and scattering (LAS) and diffused background illumination (DBI), the study characterizes spray development and mixture formation. A tracer fuel of 97.5 vol% n-tridecane and 2.5 vol% 1-methylnaphthalene (a-MN) was used to examine liquid and vapor phase distributions during evaporation. Microscopic observations compared near-field spray behavior in transient and quasi-steady states under non-evaporating conditions. Additionally, numerical simulations of nozzle flow provided insights into how nozzle geometry affects spray characteristics. The study compares the effects of small and large injection amounts on spray behavior, using 0.5 and 2.5 mg/hole for LAS experiments and 5.0 mg/hole for microscopic observations. Results show that smaller injection amounts lead to faster dilution but slower evaporation. Single-hole injectors exhibited a shorter transient period compared to multi-hole injectors under non-evaporating conditions, highlighting the impact of nozzle design. To further investigate transient spray behavior, rail pressure was adjusted to 30 MPa to match multi-hole injector profiles at 100 MPa. Injection amounts were controlled around 0.5-0.6 mg/hole. The study found that single-hole injectors had worse vapor penetration, smaller spray angles, and lower turbulent kinetic energy than multi-hole injectors, resulting in less efficient mixture formation. Simulations confirmed that multi-hole injectors induce higher turbulence, enhancing mixture formation. The book also examines split injection strategies, focusing on split ratio and dwell time. A 7:3 split ratio was optimal for achieving a homogeneous lean mixture. The improvement in mixture formation was minimal when dwell time exceeded 120 ms, and shorter penetration was observed with negative dwell times. This item is printed on demand. Shipping may be from our UK warehouse or from our Australian or US warehouses, depending on stock availability. Nº de ref. del artículo: 9789999329101
Comprar nuevo
EUR 66,10
Envío por EUR 42,79
Se envía de Reino Unido a Estados Unidos de America
Se envía de Reino Unido a Estados Unidos de America
Cantidad disponible: 1 disponibles
Imagen de archivo
Diesel Spray and Mixture Formation Processes (Paperback)
Impresión bajo demandaLibrería: AussieBookSeller, Truganina, VIC, Australia
Calificación del vendedor: 5 de 5 estrellas
Paperback. Condición: new. Paperback. This book presents an experimental study on diesel spray and mixture formation under both evaporating and non-evaporating conditions in a constant volume chamber. Using tracer laser absorption and scattering (LAS) and diffused background illumination (DBI), the study characterizes spray development and mixture formation. A tracer fuel of 97.5 vol% n-tridecane and 2.5 vol% 1-methylnaphthalene (a-MN) was used to examine liquid and vapor phase distributions during evaporation. Microscopic observations compared near-field spray behavior in transient and quasi-steady states under non-evaporating conditions. Additionally, numerical simulations of nozzle flow provided insights into how nozzle geometry affects spray characteristics. The study compares the effects of small and large injection amounts on spray behavior, using 0.5 and 2.5 mg/hole for LAS experiments and 5.0 mg/hole for microscopic observations. Results show that smaller injection amounts lead to faster dilution but slower evaporation. Single-hole injectors exhibited a shorter transient period compared to multi-hole injectors under non-evaporating conditions, highlighting the impact of nozzle design. To further investigate transient spray behavior, rail pressure was adjusted to 30 MPa to match multi-hole injector profiles at 100 MPa. Injection amounts were controlled around 0.5-0.6 mg/hole. The study found that single-hole injectors had worse vapor penetration, smaller spray angles, and lower turbulent kinetic energy than multi-hole injectors, resulting in less efficient mixture formation. Simulations confirmed that multi-hole injectors induce higher turbulence, enhancing mixture formation. The book also examines split injection strategies, focusing on split ratio and dwell time. A 7:3 split ratio was optimal for achieving a homogeneous lean mixture. The improvement in mixture formation was minimal when dwell time exceeded 120 ms, and shorter penetration was observed with negative dwell times. This item is printed on demand. Shipping may be from our Sydney, NSW warehouse or from our UK or US warehouse, depending on stock availability. Nº de ref. del artículo: 9789999329101
Comprar nuevo
EUR 91,24
Envío por EUR 31,88
Se envía de Australia a Estados Unidos de America
Se envía de Australia a Estados Unidos de America
Cantidad disponible: 1 disponibles
Imagen del vendedor
Diesel Spray and Mixture Formation Processes | Under Minimal Fuel Delivery Conditions
Impresión bajo demandaLibrería: preigu, Osnabrück, Alemania
Calificación del vendedor: 5 de 5 estrellas
Taschenbuch. Condición: Neu. Diesel Spray and Mixture Formation Processes | Under Minimal Fuel Delivery Conditions | Yu Jin | Taschenbuch | Englisch | 2025 | Eliva Press | EAN 9789999329101 | Verantwortliche Person für die EU: Libri GmbH, Europaallee 1, 36244 Bad Hersfeld, gpsr[at]libri[dot]de | Anbieter: preigu Print on Demand. Nº de ref. del artículo: 134355175
Comprar nuevo
EUR 59,10
Envío por EUR 70,00
Se envía de Alemania a Estados Unidos de America
Se envía de Alemania a Estados Unidos de America
Cantidad disponible: 5 disponibles
Imagen del vendedor
Diesel Spray and Mixture Formation Processes : Under Minimal Fuel Delivery Conditions
Impresión bajo demandaLibrería: AHA-BUCH GmbH, Einbeck, Alemania
Calificación del vendedor: 5 de 5 estrellas
Taschenbuch. Condición: Neu. nach der Bestellung gedruckt Neuware - Printed after ordering - This book presents an experimental study on diesel spray and mixture formation under both evaporating and non-evaporating conditions in a constant volume chamber. Using tracer laser absorption and scattering (LAS) and diffused background illumination (DBI), the study characterizes spray development and mixture formation. A tracer fuel of 97.5 vol% n-tridecane and 2.5 vol% 1-methylnaphthalene (¿-MN) was used to examine liquid and vapor phase distributions during evaporation.Microscopic observations compared near-field spray behavior in transient and quasi-steady states under non-evaporating conditions. Additionally, numerical simulations of nozzle flow provided insights into how nozzle geometry affects spray characteristics.The study compares the effects of small and large injection amounts on spray behavior, using 0.5 and 2.5 mg/hole for LAS experiments and 5.0 mg/hole for microscopic observations. Results show that smaller injection amounts lead to faster dilution but slower evaporation. Single-hole injectors exhibited a shorter transient period compared to multi-hole injectors under non-evaporating conditions, highlighting the impact of nozzle design.To further investigate transient spray behavior, rail pressure was adjusted to 30 MPa to match multi-hole injector profiles at 100 MPa. Injection amounts were controlled around 0.5-0.6 mg/hole. The study found that single-hole injectors had worse vapor penetration, smaller spray angles, and lower turbulent kinetic energy than multi-hole injectors, resulting in less efficient mixture formation. Simulations confirmed that multi-hole injectors induce higher turbulence, enhancing mixture formation.The book also examines split injection strategies, focusing on split ratio and dwell time. A 7:3 split ratio was optimal for achieving a homogeneous lean mixture. The improvement in mixture formation was minimal when dwell time exceeded 120 ¿s, and shorter penetration was observed with negative dwell times. Nº de ref. del artículo: 9789999329101
Comprar nuevo
EUR 72,86
Envío por EUR 61,19
Se envía de Alemania a Estados Unidos de America
Se envía de Alemania a Estados Unidos de America
Cantidad disponible: 1 disponibles